Whirlpool washer stopped working mid cycle
Whirlpool washer stopped working mid cycle. Whirlpool washers are known for their quality and reliability, but like any other appliance, they can sometimes experience problems.
One such issue is when the washer stops working mid-cycle, leaving you with a tub full of wet clothes and soapy water. This can be frustrating and inconvenient, especially if you have a busy schedule.
There are several reasons why your Whirlpool washer may stop working mid-cycle, such as a faulty motor, a malfunctioning control board, or a clogged drain.
We will explore some of the possible causes and solutions to help you get your washer back up and running smoothly.
Whirlpool washer stopped working mid cycle
By following these simple and easy steps in this article, you will be able to repair your Whirlpool washer all by yourself without getting help from a professional.
You need to follow the following steps to repair your Whirlpool washer that has stopped mid-cycle.
Step 1: Unplug the washer
The first step in working with any electrical appliance is to unplug the washer.
When it comes to an electrical appliance, it is necessary first to unplug it and proceed with further work. This Whirlpool washer works with electricity, so the first thing is to unplug it.
Doing any work while electricity is on can be dangerous to you. Flip the circuit breaker to the washer and unplug it from all the power supplies. After you are sure that all the electrical connections are removed, proceed further.
Step 2: Disassemble the washer
Now you have to disassemble your Whirlpool washer. You must remove the clips and disassemble your Whirlpool washer to do this.
To do this step, you need the help of a screwdriver, as it is difficult to do this without a screwdriver. With the help of a screwdriver, you can easily loosen the clips in less time. Also, remove the clips that run down the door seal.
Now, in this way, you can easily access the front panel of the washer and remove it to do the next step.
Step 3: Disconnect the wirings of the washer
After removing the clips and the front panel then, the next step that you have to do is to disconnect or detach the wire connector from the gasket or the door seal.
Then also, remove all the wiring of the washer. Push the tab while removing the wire connector. In this way, the wire is detached.
After this, you need to remove the control panel of the washer. Do this process carefully and cautiously remove the control panel to access the inside of the machine.
Step 4: Remove the lid switch
The lid switch has a long knob that presses down the switch and goes into the washer. This lid switch has many functions.
If this lid switch is not working, it fails to send the signals, so the washer stops the mid-cycle. You need to remove the lid switch that is damaged or is not working properly.
Step 5: Install the lid switch
The next step is installing a new lid switch in the washer. Placing the brand new switch will help your washer work properly and won’t stop the mid-cycle.
Step 6: Reassemble the washer
Finally, the next step is to reassemble the washer. This is also the last step. Put the clips back in the washer and properly reassemble the washer.
Also, slide the front panel back into the washer. Ensure you put the control and front panel properly in the washer. To do this, you need some screws to put the front panel back and reassemble the washer door.
So, In this way, you can easily repair your Whirlpool washer that stops the mid-cycle and is not functioning properly.
FAQs
Can tripping of circuit breaker cause washer to stop mid-cycle?
Yes, the tripping of the circuit breaker can result in your Whirlpool washer stopping the mid-cycle. So, if you face any problems, check your electricity and voltage. Also, inspect if your circuit breaker is working properly or if it is tripped or not.
How can I prevent my Whirlpool washer from stopping mid-cycle in the future?
Regular maintenance and care of your washer can help prevent issues from occurring, such as cleaning the lint filter, checking the drain and hoses for clogs, and ensuring that the machine is properly leveled. Avoid overloading the machine, as this can cause strain on the motor and other components.
Is it safe to continue using my Whirlpool washer if it stops working mid-cycle?
It’s best to avoid using the washer if it stops working mid-cycle, as this can cause further damage to the machine. Unplug the washer and call a professional repair technician to diagnose and fix the issue.
Conclusion
A Whirlpool washer that stops working mid-cycle can be a frustrating experience, but there are several potential solutions to this problem. First, try unplugging the washer and waiting a few minutes before plugging it back in to see if this resets the machine. Next, check for any clogs in the drain or hoses, as these can cause the machine to stop working. Regular maintenance and care of your Whirlpool washer can help prevent problems like this from occurring in the future, extending the life of your appliance and saving you time and money.
