Replace dishwasher drain hose
Replace dishwasher drain hose. A dishwasher drain hose is an essential component of a machine used for cleaning dirty dishes, as it allows the dirty water to flow out of the appliance and into the drains.
However, if an old or damaged drain hose has been installed in your dishwasher, then you may find that water starts leaking out onto your kitchen floor.
To prevent such a leaky mess from happening again and replace the old drain hose before more damage is done, read this brief guide on removing and installing a new drain hose without damaging your dishwasher.
Replace dishwasher drain hose
We will discuss here the steps of replacing the dishwasher drain hose.
Step 1: Cut Off Power
The first thing you need to do is make sure that the power is off on the dishwasher.
This can be accomplished by shutting off the circuit breaker or unplugging it entirely.
Next, you need to turn off the water supply to your unit. There will be a valve in one of these two places: either on the hose that feeds into your dishwasher or in a nearby area where the pipe provides into the wall.
Step 2: Unplug the Connector
So, next, you’ll want to unplug the connector from under the sink where the hose attaches. This connection will connect to an air gap or your sink drain tailpiece.
Below that attachment, you’ll commonly find either a worm clamp or a spring clip (the worm clamp will have a small screw head or a hex nut to loosen it; the spring clip can be pinched with pliers).
You should keep this point of connection submerged in a bucket or other container so that when water leaks out, it won’t go anywhere else and make a mess!
Step 3: Remove the Kickplate
To begin, you’ll need to remove the kickplate or bottom access panel at the bottom of your appliance. This is typically secured utilizing a few screws or bolts, depending on the type of appliance.
Unless you’re certain that your installer left enough slack in the power supply line to pull the instrument out from under the countertop.
Consider disconnecting and removing the power supply by its wiring in an electrical junction box usually found beneath your machine.
Remove the cover and twist it with a wire coat hanger; for instance, lift and disengage them from one another.
Step 4: Disconnect or Remove the Water Line
If you’re dealing with a dishwasher needing repair or installation, check to see if the unit is mounted under the counter and secured using screws – typically Phillips.
Also, disconnect or remove the water line that delivers water to the machine’s dishwasher pump.
Water can be turned off by either turning the supply valve’s handle with a wrench or simply reversing polarity to reduce power from an electronic source.
Be sure there are no leaks from gaps in connections foreign substances build up inside pipes not covered by insulation before testing a connection between wires and terminals.
Step 5: Use Pliers
Once you’ve pulled the dishwasher out, it should be easy to locate the drain hose. This is likely secured with a worm clamp or spring clip – use pliers on these, and they will open.
Next, follow the hose to where it exits the back of your dishwasher. If a nut or other mechanism secures the hose to the unit, remove it with a screwdriver.
The next part can vary depending on whether or not your dishwasher has an air gap installed. In most cases, you’ll need to go under the sink and remove both hoses from their connection points.
Either from your sink drain piping or from your air gap tool, which is usually close to your kitchen sink pipes as well as your dishwasher’s drainage system.
In this way you will easily be able to pull out any hoses connected at either end.
Step 6: Install the Hose
You should now be ready to install the new dishwasher hose. Make sure you have a fitting end over the outlet on your dishwasher’s pump.
Once securely fastened, button up your new hose with a clamp or a spring clip (usually included). You’ll have some major cleaning issues if it’s not secured properly.
Go ahead and maneuver it through the exit hole in your dishwasher. Now, if you had to remove a nut to release it from underneath the unit, as mentioned, put that back on the hook, so no more leaks are going on!
A little push here and there, and now look at how great that looks under your counter again!
FAQs
What is the size of a dishwasher drain hose?
Dishwasher hoses are measured by diameter. All dishwasher hoses extend from the sink to the garbage disposal or a dishwasher.
The most common measurement is 1/2 inch, which provides great water pressure for most homes.
Dishwasher drain hoses communicate properly with other appliances to ensure water drains down the pipes and isn’t backed up in your kitchen sink.
Why is the dishwasher drain hose corrugated?
The corrugated texture at the end of the shank makes blood flow easier, even though small and tight spaces. The ends fit on most stubs, thanks to two clamps that come with your new device, which can be attached in no time.
Related Guides
